Bosch cleaning devices provide the f04 mistake code when the water leak is discovered. The feasible sources of this error consist of:
problems with the drain of the gadget;
cuvette (powder dispenser) breakdowns;
manhole cuff failure.
Leakage of water with the drainpipe of the cleaning device
Think about the significance of the problem. Make certain to differentiate the distinction in between pipes and nozzles. So:
pipes are located outside the Bosch cleaning maker body;
branch pipelines are positioned inside the device.
The drainpipe pipeline removes drainage. After washing, a drain pump drains water from the container via this aspect. Then, water moves into the drain system. It is worth noting that in brand-new cleaning makers the nozzles are constantly solid and elastic. However, throughout procedure, the product sets. Consequently, the parts have a tendency to crack and also leakage.
What is the primary cause that provokes the circulation of the part? The reason for the problem is foreign things that get into the tool. To avoid the 04 the error code in Bosch washing machine, check laundry before washing. To fix the issue, change the spoiled part.
You can secure a worn out pipe from the device base. In this situation, two choices are possible:
the cost-free setup with a sticking out nozzle;
the alternative, when all-time low is gathered a cover and also you require to eliminate it.
The drain pipe has three connections:
with a bathtub of a washing equipment;
with a drainage system;
with a branch pipe of stress.
For replacement, loosen the clamps of these connections. Then, eliminate the pipeline. Install a new one in its place, suitable for the parameters. Tighten the clamps.
Spurt of the powder dispenser of a cleaning maker
Dripping water from the dispenser might also cause a failure of your Bosch cleaning machine. The device will certainly reveal the f04 error code on the display screen.
As a rule, this issue takes place in the following instances:
water moves from the dispenser while filling up the cleaning maker;
flow with the dispenser throughout washing as well as washing;
flow throughout the spinning time.
If the problem occurs during water obtaining, the complying with scenarios are feasible:
There is too much water pressure. Thus, the dispenser can not handle the flow. In this case, it is necessary to see to it that the device is installed degree, without turning;
Clogging of the switchgear tubes, which require cleansing;
Issues with the nozzle. There can be a powder clogging, conveniently removed by rinsing with hot water. The loss of airtightness of the branch pipe is a typical problem, too. In this instance, you have to replace it or run water with the clamps. Tighten the parts well.
When leaking occurs during washing and washing, focus on the quantity of foam. If there is extreme foaming, you can eliminate it the next way. Reduce the amount of cleaning agent or acquire one more option.
Leakages throughout rotating indicate the obstructing of the water drainage pipeline. If the tube is clogged, water is not drawn away to the sewer system. Under stress of squeezes, it becomes part of the powder tray. To fix the breakage, clean the branch pipeline.
Hatch cuffs leaking
The primary factors for this circumstance:
all-natural wear out over time, caused by severe tons, including cooling and heating. Some cleaning agents have a poor result, also. When laundry and also drum scrub the cuffs, the product loses its elasticity. With time, it ends up being delicate;
using a low quality detergent that destroys the structure of a rubber item;
the influence of clothing products, particularly metal as well as plastic. The components of the pockets, consisting of nails, screws, pins, and also coins are a major threat. A user commonly fails to remember to remove it from garments before washing.
To get rid of the damage, replace the part. The treatment takes the following steps:
Loosen up the first clamp. Plastic fasteners are weakened by a latch. Steel one can be extended by a springtime or a screw that requires to be eliminated. Hereafter, remove the first clamp.
Elimination of the front component of the cuff, hold by the special shape and also stress of the rubber.
Repairing the cuff setting. There is an unique mark, placed on the top of the component. One more one is in the storage tank. If there is no mark, repair its setting with a pencil or something.
Elimination of the 2nd clamp is a treatment similar to the initial stage. The only distinction is that the 2nd clamp is extra complicated to locate. In some cases, you need to remove the front wall of a washing equipment.
Complete cuff removal.
After that install the repair. Initially, compare the old and also the brand-new cuff. Make sure they are identical. The installment of a new element needs the adhering to actions:
Cleansing the edge of the container from contamination.
Mounting the cuff on the container. In this situation, it is required to check the coincidence of tags. Prepare to the reality that the rubber will certainly withstand, requiring some effort.
Inspecting the accuracy of the setup. There must be no clearances.
Installation of clamps.