SAMSUNG cleaning device models without a screen signal concerning the same error the next method. 2 temperature level indications 40 ° C and also Cold will certainly blink all at once. Besides that, all the washing modes signs will blink, also.
The definition of the OE error code Samsung cleaning makers
In Samsung devices, the OE code indicates a water overflow error. The tool obtains a signal from the level sensing unit (stress switch). According to that, water is more than needed for the selected program. Therefore, the home appliance quits cleaning as well as activates the drainpipe pump.
The OE error implies Overflow Mistake. The OF encoding coincides word repeating OverFlow. Although the cause can be both a real overflow of water and also incorrect analyses of the degree sensing unit (pressure button). In Samsung cleaning equipments, launched prior to 2007, the mistake code appears like E3.
How to remove the OE error code
Trigger 1— The washing machine’s proprietor applied excessive washing powder or utilized an incorrect detergent
A huge amount of powder or the incorrect choice (for instance, for hand cleaning) is the reason for the formation of bountiful foam. It enters the pressure button tube as well as creates excess stress. Because of this, the sensing unit sends a signal of the high regularity to the control module. The last one begins draining pipes the water. As a result, the OE code shows up on the Samsung washing machine screen.
To eliminate the mistake of the «incorrect» overflow due to the foam, provide the next actions. Turn on the spin mode to completely drain water, get rid of the washing and also run the device in rinse setting. It will clean out the drum. Then, switch on the washing mode again without laundry and powder. In this manner, you can check the washer’s operating. If the OE code no more lights up, then you have efficiently gotten rid of the mistake reason.
Cause 2— The maker is filled with water from the sewer system with the drainpipe tube
It is possible that your Samsung cleaning equipment is not effectively connected to the sewer. Consequently, the water from the siphon sink or drain enters into the appliance. If there is a great deal of it, the degree sensor spots it and also displays an overflow error code.
To remove the source of overflow, link the drainpipe to the sewer correctly. You can do it yourself or count on the specialist solutions of cleaning devices installing. Then drain pipes the water by running the spin setting and after that pull out the washing. For a full check, run washing with no garments. With the appropriate connection of the pipe to the sewage, flooding with drains pipes will stop. Consequently, the overflow code will no more pop out.
Create 3— Control component failure
Electronic «minds» sometimes make blunders and problem error codes without factor. You can deal with the situation by restarting the home appliance. Turn off the device with the power switch and also disconnect the cord. Leave it for 5 mins. After that plug it in power and also begin the washing again. If the mistake is «developed» by the control component, the code will certainly not brighten anymore.
However what if the reset, cleaning the powder as well as inspecting the drain hose pipe connection do not assist? The Samsung cleaning equipment constantly provides the OE mistake. So, your technique needs specialist inspecting and also repair service by an expert.
Feasible breakdowns calling for fixing
There are a number of major malfunctions, which cause the OE code to appear on the screen
Signs of an error | Possible cause of occurrence | Repair or replacement |
After turning on the Samsung washing machine:immediately shows the error code of overflow: the OE fault and so on.Or not having completed the water set, the device interrupts washing and activates draining. The display shows the OE fault code. | The water level sensor (pressure switch) is defective. The cause for that is a short circuit or the membrane damage. Therefore, the sensor signals a high water level regardless of its amount in the tank. | Replacing the pressure switch is necessary. |
There is debris in the tube or the air chamber of the pressure switch. The tube is connected to a high-pressure chamber in the sensor. In this place, a membrane with a tip is fixed to control the relay. If there is dirt in the tube or the chamber, the membrane closes the relay. Then, the sensor gives a signal of overflow even with a small water level. One of the reasons for the contamination is a wrong washing powder causing excess foaming. | “Blow” the tube and the air chamber of the pressure switch. | |
Samsung washing machine:Blocks the door and does not start washing. The 0E code immediately appears on display.or starts water draining at the same time as gaining. The appliance issues the OE overflow error code. | The electronic controller (control board) is out of order. The cause of the failure may be damage to tracks on the board, a burnt out resistor (fuse) or a breakdown (short circuit) of the microcircuits. | Solder the damaged tracks to restore contact. Replace the fuse with a new one.You can not repair a broken chip. Only the complete replacing of the controller will solve the problem. |
Samsung washing machine gains a full tank of water for 1-2 minutes after starting any washing program. Then, an overflow error appears on display. | Damage to the water inlet valve. A defective valve does not shut off the water after the stop signal.Attention! In this situation, do not wait for the overflow error code to appear! You risk flooding the bathroom or kitchen with water. Turn off the machine and de-energize it. Also, turn off the water tap. | Replace the water valve. |
After starting the washing, the appliance doesn’t gain water. After a few seconds, an overflow error occurs, and the Samsung washing machine shuts down. | There is a breakage in the circuit of the water level sensor (weak contact, wire break). The control module receives incorrect information about the overflow. It happens because of a wire break in the pressure switch circuit or burnt out contacts. Rodents often spoil wiring in devices, especially in private cottages and cottages. | You need to make a twist to connect the damaged wiring or put a new cable. Clean and, if necessary, solder the contacts. |