THERMADOR Error Code E10
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E10 | Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones. | Repair the electronic range control (also called clock or ERC) |
The control constantly checks system criteria for control as well as stove failings as well as reports a mistake code when a system problem is found. The control uses the stoves blue «on light» and oven «heating light» to report a spotted mistake code. The control will certainly continue to blink the lights in the suitable sequence as long as the mistake exists.
Detection of a fault does not prevent the ability of the control to continue to function if the mistake is not important for the intended operation. For instance: If the array door lock is defective, the array will remain to prepare since the mistake would just prevent the variety from self-cleaning.
HOW TO ANALYZE CODES
When a mistake occurs, the control will certainly flash the blue oven «on light» and heaven «heating light» sequentially to indicate the mistake. The fault codes have two numbers, these numbers are translated by the number of times the lights flash. The stove «on light» will certainly flash showing the first number, and the «heating light» will flash indicating the 2nd number.
INSTANCE:
Mistake E9 is … No Cooling Fans. The code is 43. The oven «on light» will flash 4 times, after that the «heating light» will blink 3 times, then time out. The sequence will certainly then repeat as long as the mistake exists.
ERROR CODES FOR OVENS WITH DREEFS CONTROL
The complying with graph reveals the mistake codes that can be shown in the Oven/Selector home window during particular oven breakdowns. A few of the mistake messages can be cleared by executing the adhering to actions:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |