THERMADOR Error Code E11
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E11||Turns heat off on failed oven only, micro not affected. Tweaking clears to “—” for retry.|
Turns heat off on failed oven only, micro not affected.
|CT oven; latch switch problem|
The control constantly keeps an eye on system criteria for control and oven failings and reports a mistake code when a system trouble is found. The control utilizes the stoves blue «on light» and also oven «heating light» to report a found mistake code. The control will continue to blink the lights in the suitable series as long as the fault exists.
Discovery of a mistake does not impede the capacity of the control to remain to operate if the mistake is not vital for the desired operation. As an example: If the array door latch is defective, the variety will certainly continue to cook since the fault would only protect against the variety from self-cleaning.
HOW TO ANALYZE CODES
When a mistake happens, the control will flash heaven stove «on light» as well as heaven «heating light» sequentially to indicate the mistake. The fault codes have 2 numbers, these numbers are translated by the number of times the lights blink. The stove «on light» will blink showing the initial number, and the «heating light» will flash suggesting the 2nd number.
Mistake E9 is … No Cooling Fans. The code is 43. The stove «on light» will certainly flash four times, after that the «home heating light» will certainly blink three times, after that pause. The sequence will certainly after that duplicate as long as the fault is present.
MISTAKE CODES FOR OVENS WITH DREEFS CONTROL
The following graph shows the error codes that can be presented in the Oven/Selector window during particular stove breakdowns. A few of the mistake messages can be cleared by executing the adhering to steps:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|