THERMADOR Error Code E12
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E12 | Turn the clock selector knob to Off Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window. | CT oven; latch switch problem |
The control constantly monitors system parameters for control as well as stove failures as well as reports a fault code when a system problem is discovered. The control uses the stoves blue «on light» and also oven «heating light» to report a found fault code. The control will remain to flash the lights in the ideal series as long as the mistake exists.
Detection of a mistake does not prevent the capability of the control to remain to work if the fault is not critical for the designated procedure. For example: If the variety door latch is faulty, the range will certainly continue to cook since the fault would just protect against the array from self-cleaning.
HOW TO TRANSLATE CODES
When a mistake occurs, the control will flash the blue stove «on light» and also the Blue «heating light» sequentially to show the mistake. The mistake codes have two numbers, these numbers are interpreted by the variety of times the lights blink. The stove «on light» will blink indicating the first number, as well as the «home heating light» will blink showing the second number.
EXAMPLE:
Mistake E9 is … No Cooling Followers. The code is 43. The stove «on light» will blink four times, after that the «heating light» will blink 3 times, after that time out. The series will after that duplicate as long as the fault exists.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The adhering to graph shows the mistake codes that can be presented in the Oven/Selector home window throughout particular oven malfunctions. A few of the error messages can be cleared by executing the following steps:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |