THERMADOR Error Code E14
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E14||Turn the clock selector knob to Off|
Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window
|Latch switch problems|
The control continually monitors system specifications for control and also stove failures as well as reports a mistake code when a system problem is discovered. The control uses the stoves blue «on light» and also oven «heating light» to report a spotted fault code. The control will certainly remain to blink the lights in the suitable series as long as the fault exists.
Discovery of a fault does not prevent the capacity of the control to continue to work if the mistake is not vital for the desired operation. For instance: If the range door latch is defective, the variety will continue to prepare considering that the mistake would just avoid the array from self-cleaning.
HOW TO INTERPRET CODES
When a fault happens, the control will certainly flash heaven stove «on light» as well as heaven «heating light» sequentially to indicate the mistake. The fault codes have 2 numbers, these numbers are interpreted by the number of times the lights blink. The stove «on light» will blink indicating the initial number, as well as the «heating light» will flash showing the 2nd number.
Mistake E9 is … No Air conditioning Fans. The code is 43. The oven «on light» will flash 4 times, then the «home heating light» will blink 3 times, then pause. The series will after that repeat as long as the mistake is present.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The following chart shows the error codes that can be displayed in the Oven/Selector window during specific oven malfunctions. Several of the mistake messages can be removed by performing the complying with actions:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|