THERMADOR Error Code E15
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E15||Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones.||Repair the electronic range control (also called clock or ERC)|
The control constantly keeps track of system parameters for control as well as oven failures as well as reports a mistake code when a system problem is found. The control uses the stoves blue «on light» and oven «home heating light» to report a found fault code. The control will certainly continue to blink the lights in the ideal sequence as long as the fault exists.
Detection of a fault does not hinder the capacity of the control to continue to function if the mistake is not critical for the intended operation. For instance: If the range door lock is faulty, the array will continue to prepare considering that the mistake would just stop the range from self-cleaning.
HOW TO TRANSLATE CODES
When a mistake takes place, the control will certainly flash heaven stove «on light» as well as heaven «heating light» sequentially to show the mistake. The mistake codes have 2 numbers, these numbers are translated by the variety of times the lights flash. The stove «on light» will flash indicating the first number, and the «heating light» will flash showing the second number.
Mistake E9 is … No Cooling Fans. The code is 43. The stove «on light» will blink four times, then the «home heating light» will certainly flash 3 times, then time out. The series will then repeat as long as the mistake exists.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The following graph shows the error codes that can be displayed in the Oven/Selector window during particular stove breakdowns. Several of the error messages can be cleared by performing the following steps:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|