THERMADOR Error Code E2
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E2 | Turns all heat and micro off. Clears when oven temp drops below runaway temp and selector is off. | Repair the electronic rannge control (also called clock ERC) |
The control constantly keeps track of system specifications for control and oven failings and reports a mistake code when a system trouble is discovered. The control utilizes the ovens blue «on light» and also oven «home heating light» to report an identified mistake code. The control will continue to blink the lights in the suitable sequence as long as the fault exists.
Discovery of a fault does not hinder the capability of the control to remain to function if the mistake is not vital for the designated operation. As an example: If the range door lock is inoperative, the range will certainly continue to prepare since the fault would only protect against the range from self-cleaning.
HOW TO INTERPRET CODES
When a mistake happens, the control will flash heaven stove «on light» and heaven «home heating light» sequentially to suggest the fault. The mistake codes have 2 numbers, these numbers are analyzed by the number of times the lights flash. The stove «on light» will flash suggesting the very first number, as well as the «heating light» will certainly flash indicating the 2nd number.
INSTANCE:
Mistake E9 is … No Cooling Followers. The code is 43. The oven «on light» will certainly blink 4 times, then the «home heating light» will certainly blink 3 times, then pause. The sequence will after that duplicate as long as the fault exists.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The complying with graph shows the error codes that can be displayed in the Oven/Selector window throughout specific oven breakdowns. Some of the mistake messages can be cleared by executing the adhering to actions:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |