THERMADOR Error Code E3
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E3||Turns heat off on failed oven only, micro not affected. Can be cancelled by tweaking if a good oven temperature sensor is detected.||Open oven temperature sensor (over 5000 ohms)|
The control continuously checks system specifications for control as well as oven failures as well as reports a fault code when a system trouble is detected. The control makes use of the stoves blue «on light» and oven «home heating light» to report a found fault code. The control will certainly remain to flash the lights in the proper sequence as long as the fault exists.
Detection of a fault does not hinder the ability of the control to continue to operate if the fault is not essential for the desired operation. As an example: If the variety door lock is faulty, the array will continue to prepare because the fault would only stop the array from self-cleaning.
HOW TO INTERPRET CODES
When a mistake takes place, the control will flash the blue oven «on light» and heaven «home heating light» sequentially to suggest the mistake. The fault codes have two numbers, these numbers are analyzed by the variety of times the lights flash. The oven «on light» will certainly blink indicating the very first number, and the «heating light» will certainly blink showing the 2nd number.
Error E9 is … No Air conditioning Fans. The code is 43. The oven «on light» will flash four times, after that the «home heating light» will certainly flash three times, after that time out. The sequence will after that repeat as long as the fault exists.
MISTAKE CODES FOR OVENS WITH DREEFS CONTROL
The following chart shows the error codes that can be displayed in the Oven/Selector window during details stove breakdowns. A few of the mistake messages can be cleared by executing the complying with actions:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|