THERMADOR Error Code E6
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E5||Disables clean mode in both ovens, allows cook and microwave. Can be tweaked away for retry. User must unlatch and delete the “—” to try to re-latch the door.||Repair the electronic range control (also called clock or ERC)|
The control constantly checks system specifications for control and stove failures as well as reports a fault code when a system issue is identified. The control utilizes the ovens blue «on light» as well as oven «home heating light» to report a found mistake code. The control will certainly continue to blink the lights in the ideal sequence as long as the mistake exists.
Detection of a fault does not prevent the capability of the control to continue to operate if the mistake is not crucial for the intended procedure. For example: If the variety door latch is inoperative, the array will certainly continue to cook because the mistake would just protect against the range from self-cleaning.
HOW TO INTERPRET CODES
When a mistake occurs, the control will certainly blink the blue stove «on light» and the Blue «heating light» sequentially to indicate the mistake. The fault codes have two numbers, these numbers are translated by the variety of times the lights flash. The oven «on light» will certainly blink suggesting the initial number, as well as the «heating light» will blink suggesting the second number.
Mistake E9 is … No Cooling Fans. The code is 43. The oven «on light» will certainly flash 4 times, after that the «heating light» will flash three times, after that pause. The series will certainly after that duplicate as long as the mistake is present.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The adhering to chart reveals the mistake codes that can be presented in the Oven/Selector home window during details stove breakdowns. Some of the error messages can be cleared by executing the complying with steps:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|