THERMADOR Error Code E7
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E7||Turns heat off on failed oven only, micro not affected. Cleared with a mode change.||Illegal temp display turn off and retry|
The control constantly keeps track of system parameters for control as well as stove failings and also reports a mistake code when a system issue is identified. The control utilizes the stoves blue «on light» and oven «home heating light» to report a found fault code. The control will continue to flash the lights in the proper sequence as long as the fault exists.
Detection of a mistake does not impede the capability of the control to continue to operate if the mistake is not essential for the desired operation. For example: If the array door lock is inoperative, the array will continue to cook because the fault would only stop the array from self-cleaning.
HOW TO TRANSLATE CODES
When a fault occurs, the control will flash heaven stove «on light» and also the Blue «heating light» sequentially to suggest the mistake. The fault codes have two numbers, these numbers are interpreted by the number of times the lights blink. The oven «on light» will blink showing the very first number, and also the «heating light» will certainly flash suggesting the 2nd number.
Error E9 is … No Air conditioning Followers. The code is 43. The oven «on light» will blink 4 times, after that the «heating light» will flash 3 times, after that time out. The series will certainly after that repeat as long as the mistake is present.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The following chart reveals the error codes that can be presented in the Oven/Selector home window throughout details stove malfunctions. Several of the mistake messages can be removed by executing the following actions:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|