THERMADOR Error Code E8
Professional Ranges Models: PDR30/36/48…PRG30/36/48
|CODE E8||Turns heat off on failed oven only, micro not affected. Error will remain in display until repaired and powered up. No error tones.Turns heat off on failed oven only, micro not affected.||Repair the electronic range control (also called clock or ERC)|
The control continually keeps track of system parameters for control and also stove failures and also reports a fault code when a system issue is detected. The control makes use of the ovens blue «on light» and oven «heating light» to report a spotted mistake code. The control will certainly continue to blink the lights in the appropriate series as long as the fault exists.
Detection of a mistake does not prevent the ability of the control to continue to function if the fault is not vital for the desired procedure. As an example: If the array door lock is faulty, the array will remain to prepare considering that the mistake would only stop the range from self-cleaning.
HOW TO INTERPRET CODES
When a fault takes place, the control will blink the blue oven «on light» and the Blue «home heating light» sequentially to show the fault. The mistake codes have 2 numbers, these numbers are translated by the number of times the lights blink. The oven «on light» will flash indicating the initial number, as well as the «home heating light» will certainly flash indicating the second number.
Mistake E9 is … No Cooling Fans. The code is 43. The oven «on light» will blink 4 times, after that the «home heating light» will certainly blink three times, after that pause. The sequence will certainly after that repeat as long as the fault is present.
ERROR CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart shows the error codes that can be presented in the Oven/Selector window during particular oven malfunctions. Several of the mistake messages can be cleared by performing the complying with steps:
|ERROR MESSAGE||ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|E1||C&E||Control board problem.|
|E2||G&K||Cook or Clean mode runaway (temp >635 °F)|
Clean mode runaway (clean temp +32 °F).
|E3||A&H||Open oven temperature sensor (>5000 Ω).|
|E4||A&H||Shorted oven temperature sensor (<5000 Ω).|
|E5||K&D||Control board too cold, too hot, or defective.|
|E6||C&J||Control board problem.|
|E7||A&I||Illegal temperature display. Turn off oven and try again.|
|E8||A&D||Control board problem.|
|E9||A&E||Latch switch problem.|
|E10||B&D||Control board problem.|
|E11||A&F||CT oven – latch switch problem|
|E12||A&E||CT ovens – latch switch problem|
|E13||A&C||CT ovens – latch frozen or no power to latch motor.|
CMT ovens – control board not converted (refer to page 3-7 for conversion data).
|E14||A&E||Latch switch problem.|
|E15||B&D||Control board problem.|
|ERROR CODE NOTES||DESCRIPTION OF PROBLEM|
|A||Turns heat off on the failed oven only; microwave not affected.|
|B||Turns all heat off; microwave not affected.|
|C||Disables the CLEAN mode in both ovens; allows COOK and microwave.|
|D||Error will remain in the display until oven is repaired and powered back up. No error tones.|
|E||Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.|
|F||Tweaking clears to “—“ for retry.|
|G||Clears when the oven temperature is less then the runaway temperature with the selector switch off.|
|H||Can be cancelled by tweaking if a good sensor is detected.|
|I||Cleared with a mode change.|
|J||Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.|
|K||Turns heat and microwave off.|
|L||If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.|