THERMADOR Error Code E9
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E9 | Turn the clock selector knob to OFF Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window. | Latch switch problems |
The control continuously monitors system specifications for control and also stove failings as well as reports a fault code when a system problem is detected. The control makes use of the stoves blue «on light» and also oven «home heating light» to report a detected mistake code. The control will certainly remain to flash the lights in the ideal sequence as long as the mistake exists.
Detection of a mistake does not impede the capacity of the control to remain to function if the mistake is not important for the designated procedure. As an example: If the array door latch is faulty, the variety will certainly remain to prepare since the fault would only protect against the variety from self-cleaning.
HOW TO TRANSLATE CODES
When a fault happens, the control will certainly blink the blue oven «on light» and heaven «home heating light» sequentially to show the fault. The mistake codes have two numbers, these numbers are analyzed by the number of times the lights blink. The oven «on light» will flash showing the initial number, and also the «home heating light» will certainly blink showing the second number.
INSTANCE:
Mistake E9 is … No Cooling Fans. The code is 43. The oven «on light» will certainly flash 4 times, then the «home heating light» will blink 3 times, then time out. The sequence will after that duplicate as long as the mistake is present.
MISTAKE CODES FOR OVENS WITH DREEFS CONTROL
The following graph shows the mistake codes that can be displayed in the Oven/Selector home window throughout particular stove malfunctions. Several of the mistake messages can be removed by doing the following steps:
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |